3 Safety Tether Kill Switch...
  • 3 Safety Tether Kill Switch...
  • 3 Safety Tether Kill Switch...

3 Safety Tether Kill Switch TAO MOTORS RAPTOR 125 ATV

$24.99
Il n'y a pas encore d'avis.
109514 Safety Tether Kill Switch for TAO MOTORS RAPTOR 125 ATV

Genuine OEM safety tether kill switch designed for the TAO MOTORS RAPTOR 125cc ATV.

Also known as an engine stop switch or tether safety switch, this component is designed to stop the engine when its removable safety cap is pulled from the switch.

The safety tether is intended to be attached to the rider, allowing the engine stop mechanism to activate if the rider becomes separated from the ATV.

Features a 2-wire electrical connection according to replacement parts suppliers.

Designed for compatible handlebar mounting and original engine stop circuits.

Ideal for replacing a broken, damaged or malfunctioning original safety kill switch.

Genuine TAO MOTORS OEM replacement part available at EcoBike Canada.

 

Security garantes

 

Quick delivery

Safety Tether Kill Switch for TAO MOTORS RAPTOR 125 ATV

The 109514 Safety Tether Kill Switch is a genuine OEM TAO MOTORS replacement part designed for the engine stop safety system of the RAPTOR 125cc ATV.

Also known as an engine stop switch, tether switch, safety lanyard kill switch or emergency engine stop switch, this component allows the vehicle's engine stop circuit to be activated when the safety tether mechanism is triggered.

Unlike a basic manual engine stop button, a tether kill switch uses a removable safety cap connected to a cord.

When installed and connected correctly, removing the safety cap from the switch activates the engine stop function on the compatible vehicle.

The tether is designed to be attached to the rider so that separation from the ATV can pull the cap from the switch.

Part number 109514 is identified in the TAO MOTORS ATA125-K parts catalog as Tether Switches ATA110-B.

It appears at diagram position 3 in the steering system assembly.

This genuine OEM replacement component is intended for a damaged or malfunctioning original tether kill switch.

IMPORTANT: This product is sold individually. One safety kill switch assembly is supplied per quantity ordered, not a package of multiple switches.

Why Choose the Genuine OEM 109514 Safety Kill Switch?

  • Genuine OEM TAO MOTORS replacement part.
  • Original manufacturer part number: 109514.
  • Listed for the RAPTOR 125cc ATV.
  • Manufacturer designation: Tether Switches ATA110-B.
  • Safety tether-style engine stop switch.
  • Designed for a removable safety cap and lanyard.
  • Two-wire electrical connection according to suppliers.
  • Designed for compatible handlebar mounting.
  • Helps restore the original engine stop safety function.
  • Replaces a damaged or malfunctioning switch.
  • Suitable for ATV electrical system repairs.
  • Sold individually.

An Important ATV Safety Component

The TAO MOTORS RAPTOR 125 is equipped with several components designed to allow the rider to operate and control the vehicle.

The safety tether kill switch provides an additional method of activating the engine stop circuit.

This type of device is especially useful when the rider becomes separated from the ATV.

The removable safety cap is designed to remain connected to the rider through a tether cord.

When the tether pulls the cap from the switch, the corresponding engine stop system is activated.

This function depends on correct installation, an appropriate electrical connection and a working engine stop circuit.

Important: A tether kill switch does not replace proper riding practices, effective brakes or adult supervision where applicable. It cannot guarantee that every dangerous situation will be prevented.

How Does a Tether Kill Switch Work?

A tether kill switch uses an electrical switching mechanism controlled by a removable cap.

The cap is connected to a safety lanyard that can be attached to the rider according to the vehicle manufacturer's instructions.

During normal operation, the cap remains correctly positioned on the switch.

If the cap is pulled away, the switch changes its electrical state.

On a properly configured vehicle, this activates the engine stop circuit and shuts down the engine.

The exact electrical switching behavior depends on the original ignition and engine stop system.

For this reason, the correct OEM reference is important when replacing the original component.

Do not substitute a different electrical switch unless its operating characteristics and wiring compatibility have been verified.

Two-Wire Electrical Connection

Replacement parts suppliers identify part number 109514 as a two-wire tether kill switch.

One supplier describes an assembly featuring a two-position male electrical connector and a wiring pigtail attached to the switch.

This connection is intended to interface with the corresponding engine stop circuit.

Before ordering or installing the replacement, verify:

  • The number of wires on the original switch.
  • The shape of the electrical connector.
  • The male or female connector configuration.
  • The required wire harness length.
  • The original mounting position.
  • The safety cap and tether configuration.
  • The electrical operation required by the vehicle.

Harness lengths and mounting dimensions may vary between replacement versions.

Important: Two switches are not automatically interchangeable simply because both have two wires.

Designed for Handlebar Mounting

Part number 109514 appears in the ATA125-K steering system parts diagram alongside the handlebar and associated control components.

Specialized suppliers describe this style of replacement kill switch as a handlebar-mounted assembly.

The switch should be mounted in a suitable position that does not interfere with steering, throttle operation or brake controls.

The tether must also be positioned so that it can operate correctly without becoming caught on other vehicle components.

The electrical wiring should be routed away from moving parts, sharp edges and excessive heat.

Correct mounting and cable routing help maintain the intended safety function of the assembly.

Removable Safety Cap and Tether Cord

Part number 109514 is identified as a tether-style safety switch.

Supplier-listed assemblies for this reference feature a switch, a removable safety cap and a tether cord.

The cap is designed to engage the switch mechanism, while the tether provides the connection to the rider.

The exact tether style, length and included components should be confirmed against the EcoBike-stocked product.

The replacement cap must fit the switch correctly to ensure proper operation.

Do not use improvised retaining devices or modifications that could prevent the safety tether from releasing as designed.

Difference Between Kill Switch 109514 and Handlebar Switch 116309

The RAPTOR 125 uses several separate electrical and mechanical components around the handlebars.

  • 109514 – Safety Tether Kill Switch: Removable tether-style switch designed to activate the engine stop circuit.
  • 116309 – Left Handlebar Switch: Separate electrical control assembly.
  • 603876 – Handlebar: Main steering handlebar component.
  • 101676 – Handlebar Clamp: Mounting component used to secure the handlebar.
  • 109414 – Brake/Throttle Control Assembly: Separate riding control component.

These components perform different functions in the vehicle.

The 109514 tether kill switch should not be confused with the ignition key switch, starter button or a multifunction handlebar switch.

This listing is specifically for genuine OEM part number 109514.

When Should a Safety Kill Switch Be Replaced?

The engine stop switch may be exposed to vibration, dust, moisture and accidental impacts during ATV operation.

Over time, electrical connections or mechanical parts can become damaged.

Replacement may be necessary if the original switch shows:

  • A cracked or broken switch housing.
  • A removable cap that no longer fits correctly.
  • A missing or damaged safety tether.
  • Cut or damaged electrical wires.
  • A loose or corroded connector.
  • A defective internal switching mechanism.
  • Intermittent operation of the engine stop circuit.
  • Damage caused by a fall or impact.
  • Failure discovered during electrical system inspection.

Any suspected failure of a safety-related component should be investigated before the ATV is used again.

Can a Defective Kill Switch Prevent the Engine from Starting?

On certain ATV electrical systems, the tether kill switch must be in its normal operating state for the engine to run.

A missing safety cap, faulty electrical contact or damaged harness can therefore contribute to a no-start condition.

However, starting problems may also originate from the battery, ignition switch, ignition system, wiring or fuel system.

The kill switch should not automatically be assumed to be the cause of every starting problem.

Proper troubleshooting is required to identify the defective component.

Do not bypass or permanently disable the safety switch to operate the vehicle. Repair the system using compatible replacement parts.

Replacement and Installation

Before replacing the switch, make sure the ATV is stationary and the engine is off.

Disconnect electrical power as required by the manufacturer's service instructions.

Locate the original tether kill switch and identify its mounting position, electrical connector and cable routing.

Compare the new switch with the original part.

Confirm the mounting configuration, connector type, wire count and removable safety cap arrangement.

Install the replacement switch in the proper position without restricting steering or other handlebar controls.

Route the wiring away from moving parts, hot surfaces and potential pinch points.

Reconnect the electrical harness according to the original vehicle configuration.

After installation, test the engine stop function under controlled and safe conditions.

Do not alter the wiring to defeat the safety system. If the installation or electrical operation is uncertain, have the repair performed by a qualified technician.

Important Safety Checks After Installation

The safety tether switch should be inspected before the ATV is returned to service.

Recommended checks include:

  • Verify secure mounting of the switch.
  • Check that the safety cap fits correctly.
  • Confirm that the tether can move freely.
  • Inspect the wiring for excessive tension.
  • Verify the electrical connector is fully engaged.
  • Check the condition of the cable insulation.
  • Confirm normal operation with the safety device correctly installed.
  • Verify that triggering the switch activates the expected engine stop function.

Tests should be carried out with the vehicle immobilized in a safe environment.

If the engine fails to stop when the safety device is triggered, the electrical system must be inspected and repaired before further operation.

Vehicle Compatibility

  • Brand: TAO MOTORS / TAOTAO
  • Model: RAPTOR 125
  • Engine size: 125cc
  • OEM part number: 109514
  • Manufacturer designation: Tether Switches ATA110-B
  • Alternate designation: Safety Tether Kill Switch
  • Application: Engine stop safety circuit
  • Mounting location: Handlebar, according to original configuration
  • Category: Handlebar and steering / Electrical system

Part number 109514 is also listed by certain suppliers for TAO MOTORS REX ATVs and DB20 dirt bikes, as well as selected compatible vehicles from other manufacturers.

Always confirm the original switch reference, connector configuration and electrical compatibility before ordering for another model.

Technical Specifications

  • Part number: 109514
  • Part name: Safety Tether Kill Switch
  • Alternate names: Engine Stop Switch / Tether Switch
  • Manufacturer catalog name: Tether Switches ATA110-B
  • Component type: Electrical safety switch
  • Function: Activates the engine stop circuit when triggered
  • Electrical connection: Two-wire design according to suppliers
  • Connector: Two-position connector according to supplier-listed version
  • Mounting location: Handlebar
  • ATA125-K diagram position: 3
  • Safety mechanism: Removable cap and tether
  • Exact wire harness length: Verify stocked component
  • Mounting dimensions: Verify actual part
  • Quality: Genuine OEM replacement part
  • Vehicle: TAO MOTORS RAPTOR 125cc ATV
  • Packaging: Sold individually
  • Quantity included: 1 safety kill switch assembly
  • Exact tether and accessory contents: Confirm EcoBike inventory

Frequently Asked Questions

What is the purpose of the 109514 safety kill switch?

It activates the vehicle's engine stop circuit when the removable safety tether cap is pulled from the switch.

Is this switch compatible with the RAPTOR 125 ATV?

Yes. Part number 109514 is listed at position 3 in the TAO MOTORS ATA125-K steering system parts catalog.

Is this a regular engine stop button?

No. It is a tether-style safety kill switch designed to operate with a removable cap and safety cord.

How many wires does the switch have?

Suppliers identify part number 109514 as a two-wire safety tether kill switch.

Is the safety tether included?

Supplier-listed versions include a removable cap and tether cord. The exact contents of the EcoBike-stocked assembly should be confirmed.

Can a defective tether switch prevent the ATV from starting?

Yes, depending on the electrical configuration. A missing safety cap, faulty contact or damaged wiring can contribute to a no-start condition.

Is this the same component as left handlebar switch 116309?

No. Part number 109514 identifies the safety tether kill switch. Part number 116309 is a separate left handlebar electrical switch assembly.

Can I bypass the kill switch?

The safety switch should not be disabled or bypassed during vehicle operation. A defective switch must be repaired or replaced properly.

Is this a genuine OEM replacement part?

Yes. Part number 109514 identifies a genuine OEM TAO MOTORS replacement safety tether switch.

Is the kill switch sold individually?

Yes. One safety kill switch assembly is included per quantity ordered.

Why Buy TAO MOTORS Parts from EcoBike?

At EcoBike Canada, we offer a selection of genuine OEM replacement parts for TAO MOTORS ATVs.

Our parts catalog includes safety tether switches, engine stop switches, handlebar controls, ignition switches, electrical wiring components, handlebars and other replacement parts.

Benefit from our customer service, OEM replacement parts selection and experience with recreational vehicle assembly, maintenance and repairs.

EcoBike – Your Canadian Source for Genuine TAO MOTORS OEM Parts.

www.eco-bike.ca

109514-Tether Switches

Specific References