Genuine OEM castle nut designed for compatible front wheel spindle fastening assemblies on the TAO MOTORS RAPTOR 125cc ATV.
Features an M14 nominal thread diameter of 14 mm and a fine thread pitch of 1.5 mm.
Its castellated design allows installation of a compatible cotter pin to help prevent accidental loosening.
Ideal for replacing a worn, damaged or missing original castle nut while preserving the factory fastening configuration.
Thread size: M14 x 1.5 mm.
Sold individually – Cotter pin not included.
Genuine TAO MOTORS OEM replacement part available at EcoBike Canada.
Security garantes
Quick delivery
The 105326 M14 x 1.5 Castle Nut is a genuine OEM TAO MOTORS replacement fastener designed for corresponding front suspension and wheel spindle assemblies on the RAPTOR 125cc ATV.
Identified in the manufacturer's catalog as Castle Nut M14 x 1.5, this fastening component features a nominal thread diameter of 14 mm and a fine thread pitch of 1.5 mm.
The nut features a castellated upper section with slots designed to accommodate a cotter pin when installed on a compatible drilled shaft.
When properly installed, this mechanical retaining system helps prevent unintended nut rotation and loosening.
Part number 105326 appears in the ATA125-K front suspension parts catalog alongside the wheel spindle and related fastening components.
It is ideal for replacing a worn, damaged or missing original castle nut while preserving the manufacturer's fastening specifications.
IMPORTANT: This product is sold individually. One M14 x 1.5 castle nut is included per quantity ordered. Cotter pin and other mounting hardware are sold separately.
The front suspension system of the TAO MOTORS RAPTOR 125 includes control arms, wheel spindles, hubs, washers, nuts and retaining hardware.
These mechanical components must remain correctly assembled during vehicle operation.
The 105326 castle nut forms part of the corresponding front suspension fastening arrangement.
Its castellated design allows an additional retaining feature when used with the specified cotter pin and a compatible drilled shaft.
Using the correct OEM replacement fastener is important for maintaining the original assembly configuration.
A castle nut, also called a castellated nut, features slots around its upper section.
These slots allow a cotter pin to pass through a matching hole in a compatible threaded shaft.
After the nut is tightened according to the manufacturer's instructions, the slots are aligned with the drilled hole using the prescribed assembly procedure.
The cotter pin is inserted, and its ends are bent to secure it in place.
This arrangement helps prevent the nut from rotating unintentionally after installation.
Important: A castle nut must not be operated without its required retaining pin when the original assembly specifies one.
The 105326 castle nut features the following specifications:
Both thread diameter and pitch must match the mating threaded shaft.
Important: An M14 nut with a different thread pitch is not an appropriate replacement for an M14 x 1.5 mm castle nut.
Using incompatible threads may damage the mounting component and compromise the fastening assembly.
In the ATA125-K front suspension parts diagram, castle nut 105326 appears at position 16.
The same diagram lists 105340 – Cotter Pin 3 x 40 mm at position 15.
Part number 105414 is also listed as a corresponding front suspension washer.
These parts form part of the manufacturer's fastening arrangement for the relevant assembly.
The cotter pin and washer are not included in this castle nut listing.
Always verify the required fasteners and retaining hardware for your specific ATV configuration.
A castle nut uses a castellated upper section and a cotter pin for mechanical retention.
A locknut uses a different locking design to increase resistance to loosening.
Although different nut types may share similar thread dimensions, they are not automatically interchangeable.
Always use the fastening type specified by the manufacturer for the original assembly.
Castle nuts should be inspected whenever a corresponding wheel or suspension assembly is disassembled.
Replacement may be necessary if the original nut shows:
Inspect the threaded shaft, washer and cotter pin at the same time for additional damage.
Before installation, compare the new castle nut with the original component to confirm the thread diameter, pitch and overall configuration.
Inspect the mating threads and the retaining pin hole in the spindle or shaft.
Install the nut using the manufacturer's recommended assembly procedure and tightening specifications.
Follow the prescribed method for aligning the castellated slots with the retaining hole. Do not arbitrarily loosen or overtighten the nut to achieve alignment.
Install a new cotter pin of the appropriate size and bend its ends according to the required procedure.
After installation, inspect the wheel assembly for correct fastening and abnormal play before operating the ATV.
Professional installation is recommended for safety-critical wheel and suspension components.
The ATA125-K front suspension parts catalog lists 2 castle nuts with part number 105326 in the complete front suspension assembly.
One is used in each corresponding left and right front wheel assembly.
This is the quantity specified for the vehicle, not the number of nuts included in this product listing.
To replace one castle nut, order a quantity of 1. To replace both, order a quantity of 2.
This part number is also used on certain other TAO MOTORS ATVs, including the REX 125.
Before ordering for another vehicle, compare the original part reference and fastening specifications.
It secures the corresponding front wheel spindle assembly and allows mechanical retention with a compatible cotter pin.
The nut features an M14 nominal diameter of 14 mm and a fine thread pitch of 1.5 mm.
The ATA125-K front suspension diagram lists part number 105340, a 3 x 40 mm cotter pin, alongside the corresponding fastening components.
No. This product includes the castle nut only. Cotter pins and additional mounting hardware are sold separately.
Part number 105326 is an M14 x 1.5 mm castle nut, while part number 105320 is an M10 x 1.25 mm castle nut. They have different thread dimensions and are not interchangeable.
Yes. Part number 105326 is listed in the ATA125-K family front suspension catalog used for the TAO MOTORS RAPTOR 125cc ATV.
Yes. This listing is for genuine OEM TAO MOTORS part number 105326.
Yes. Each quantity ordered includes one castle nut. To replace both front wheel fastening nuts, select a quantity of two.
At EcoBike Canada, we offer a selection of genuine OEM replacement parts for TAO MOTORS ATVs.
Our parts selection includes castle nuts, cotter pins, washers, bolts, wheel spindles, wheel bearings, hubs and suspension components.
Benefit from our customer service, replacement parts selection and experience with recreational vehicle maintenance and repairs.
EcoBike – Your Canadian Source for Genuine TAO MOTORS OEM Parts.
www.eco-bike.ca