17 Flat washer TAO MOTORS...
  • 17 Flat washer TAO MOTORS...
  • 17 Flat washer TAO MOTORS...

17 Flat washer TAO MOTORS RAPTOR 125 ATV

$0.99
Il n'y a pas encore d'avis.
105414 Flat Washer 14 x 40 x 2 mm for TAO MOTORS RAPTOR 125 ATV

Genuine OEM flat washer designed for corresponding front suspension fastening assemblies on the TAO MOTORS RAPTOR 125cc ATV.

Features a nominal 14 mm inside diameter, 40 mm outside diameter and 2 mm thickness.

Its wide bearing surface helps distribute clamping pressure and protect the mounted components.

Ideal for replacing a worn, bent, damaged or missing original washer.

Dimensions: 14 x 40 x 2 mm.

Sold individually – One washer included.

Genuine TAO MOTORS OEM replacement part available at EcoBike Canada.

 

Security garantes

 

Quick delivery

Flat Washer 14 x 40 x 2 mm for TAO MOTORS RAPTOR 125 ATV

The 105414 Flat Washer is a genuine OEM TAO MOTORS replacement part designed for corresponding front suspension fastening assemblies on the RAPTOR 125cc ATV.

Identified in the parts catalog as Flat Washer 14 x 40 x 2 mm, this component features a nominal inside diameter of 14 mm, an outside diameter of 40 mm and a nominal thickness of 2 mm.

Part number 105414 is listed in the ATA125-K front suspension assembly, alongside the corresponding front wheel spindle fastening components.

Its wide bearing surface helps distribute clamping force between the fastener and the mounted components.

It is ideal for replacing a bent, damaged, worn or missing original washer while preserving the factory fastening arrangement.

IMPORTANT: This washer is sold individually. One flat washer is included per quantity ordered.

Why Choose the Genuine OEM 105414 Flat Washer?

  • Genuine OEM TAO MOTORS replacement part.
  • Original part number: 105414.
  • Listed for the RAPTOR 125cc ATV front suspension.
  • Nominal inside diameter: 14 mm.
  • Outside diameter: 40 mm.
  • Nominal thickness: 2 mm.
  • Wide, flat circular design.
  • Helps distribute fastening pressure.
  • Provides a bearing surface for the corresponding assembly.
  • Replaces worn, damaged or missing factory washers.
  • Sold individually.

An Important Front Suspension Fastening Component

The front suspension system of the TAO MOTORS RAPTOR 125 includes suspension arms, front wheel spindles, hubs, nuts, washers and retaining hardware.

These components must be assembled using the fastening arrangement specified by the manufacturer.

The 105414 flat washer provides a bearing surface between the associated fastening components.

Its 40 mm outside diameter helps spread clamping pressure over a relatively wide area.

A damaged or deformed washer may affect how the fastener contacts the mounting surface.

Using the correct OEM replacement helps maintain the intended mounting configuration.

Original 14 x 40 x 2 mm Dimensions

The 105414 flat washer features the following nominal specifications:

  • Inside diameter: 14 mm.
  • Outside diameter: 40 mm.
  • Thickness: 2 mm.
  • Shape: Flat and circular.
  • OEM reference: 105414.

The inside diameter must be suitable for the corresponding mounting component.

The outside diameter and thickness are also important for maintaining the original bearing surface and assembly spacing.

Important: Always compare the replacement washer with the original part, as washers with similar dimensions are not necessarily interchangeable.

Use in the Front Wheel Spindle Assembly

The ATA125-K parts catalog lists the 105414 Flat Washer at diagram position 17 of the front suspension assembly.

Other nearby fastening components include:

  • 105326: M14 x 1.5 Castle Nut.
  • 105340: 3 x 40 mm Cotter Pin.
  • 105414: 14 x 40 x 2 mm Flat Washer.

These components are listed in the section associated with the front wheel spindle fastening assemblies.

The flat washer provides a bearing surface, while the castle nut and cotter pin perform their respective fastening and retaining functions.

This product includes the flat washer only. The castle nut, cotter pin and other components are sold separately.

Flat Washer vs. Spring Washer

A flat washer primarily provides a bearing surface and helps distribute clamping pressure.

A spring washer features a different design intended to provide elastic action within a fastening assembly.

These two types of washers are not automatically interchangeable.

Part number 105414 is a flat washer, not a spring lock washer.

Always use the washer type specified for the original fastening assembly.

When Should a Flat Washer Be Replaced?

Flat washers should be inspected whenever the corresponding wheel or suspension fastening assembly is disassembled.

Replacement may be necessary if the original washer shows:

  • Visible bending or deformation.
  • Cracks or other mechanical damage.
  • Excessive wear on its bearing surfaces.
  • Significant corrosion.
  • Damage caused by incorrect tightening.
  • A missing original washer.
  • Damage discovered during fastener replacement.

Inspect the associated nuts, wheel spindles and mounting surfaces for additional damage.

Replacement and Installation

Before installation, compare the new washer with the original component to verify its dimensions and configuration.

Clean the mounting surfaces and inspect the associated fasteners.

Position the washer according to the manufacturer's assembly diagram.

Follow the specified tightening procedure and torque requirements for the corresponding fastener.

If the assembly uses a castle nut, confirm that the required cotter pin is properly installed.

After reassembly, inspect the wheel fastening components for secure mounting and abnormal play before operating the ATV.

How Many Washers Are Used on the RAPTOR 125?

The ATA125-K front suspension parts catalog lists 2 washers with part number 105414 for the complete front suspension assembly.

This is the quantity shown in the vehicle parts diagram, not the number included in this product listing.

To replace one washer, order a quantity of 1. To replace both corresponding washers, order a quantity of 2.

Vehicle Compatibility

  • Brand: TAO MOTORS / TAOTAO
  • Model: RAPTOR 125
  • Engine size: 125cc
  • OEM part number: 105414
  • Manufacturer description: Flat Washer
  • Nominal dimensions: 14 x 40 x 2 mm
  • Application: Corresponding front suspension fastenings
  • Category: Front end and suspension

Part number 105414 is also listed for certain other TAO MOTORS ATVs, including the REX 125.

Always verify the original part reference, dimensions and mounting configuration before ordering for another vehicle.

Technical Specifications

  • Part number: 105414
  • Part name: Flat Washer
  • Nominal inside diameter: 14 mm
  • Outside diameter: 40 mm
  • Nominal thickness: 2 mm
  • Shape: Flat circular washer
  • Component type: Mechanical fastening washer
  • Application: Front suspension / wheel spindle assembly
  • Category: Front suspension hardware
  • ATA125-K diagram position: 17
  • Quantity listed for complete assembly: 2
  • Quality: Genuine OEM replacement part
  • Vehicle: TAO MOTORS RAPTOR 125cc ATV
  • Package: Sold individually
  • Quantity included: 1 washer
  • Castle nut and cotter pin: Not included

Frequently Asked Questions

What are the dimensions of the 105414 flat washer?

It is listed with a nominal 14 mm inside diameter, 40 mm outside diameter and 2 mm thickness.

What is this washer used for?

It provides a bearing surface for the corresponding fastening assembly and helps distribute clamping pressure over the mounted component.

Is this washer compatible with the RAPTOR 125 ATV?

Yes. Part number 105414 appears in the ATA125-K front suspension parts catalog.

How many washers are used in the front suspension?

The ATA125-K parts diagram lists two washers with part number 105414 for the complete front suspension assembly.

Is this a spring lock washer?

No. Part number 105414 is a flat washer and should not be confused with a spring washer.

Is the 105326 castle nut included?

No. This listing includes only the flat washer. The castle nut and cotter pin are separate replacement parts.

Is this a genuine OEM replacement part?

Yes. This is a genuine OEM TAO MOTORS replacement washer.

Is the washer sold individually?

Yes. Each quantity ordered includes one washer. To purchase two washers, select a quantity of two.

Why Buy TAO MOTORS Parts from EcoBike?

At EcoBike Canada, we offer a selection of genuine OEM replacement parts for TAO MOTORS ATVs.

Our parts selection includes flat washers, castle nuts, cotter pins, bolts, bearings, wheel hubs and other suspension and steering components.

Benefit from our customer service, replacement parts selection and experience with recreational vehicle maintenance and repairs.

EcoBike – Your Canadian Source for Genuine TAO MOTORS OEM Parts.

www.eco-bike.ca

105414-Flat Washer

Specific References