Genuine OEM nylon bushing designed for the front suspension A-arm assemblies of the TAO MOTORS RAPTOR 125cc ATV.
Used in suspension pivot connections to help guide A-arm movement and reduce friction between mechanical components.
Original dimensions: 30 x 25 x 18 x 20 mm.
Ideal for replacing a worn, cracked, deformed or damaged suspension bushing, or one showing excessive play.
Helps restore the original front suspension mounting configuration.
Sold individually – One nylon bushing.
Genuine TAO MOTORS OEM replacement part available at EcoBike Canada.
Security garantes
Quick delivery
The 112930 Nylon Bushing is a genuine OEM TAO MOTORS replacement part designed for the RAPTOR 125cc ATV front suspension system.
Also known as a front A-arm bushing or suspension control arm bushing, this component is used in the corresponding pivot assemblies of the front suspension arms.
Its nominal dimensions are 30 x 25 x 18 x 20 mm, as specified for OEM part number 112930.
The nylon bushing helps guide suspension arm movement while reducing direct friction between the associated mechanical components.
Replacing a worn or damaged bushing helps restore the intended fit and operation of the suspension pivot assembly.
IMPORTANT: This listing is prepared for individual sale. One nylon bushing is included per quantity ordered.
The TAO MOTORS RAPTOR 125 front suspension includes upper and lower A-arms, mounting spacers, bolts, nuts and other fastening components.
Nylon bushings are used at specific suspension pivot points to provide a bearing surface between the moving and supporting components.
They help guide the intended movement of the suspension arms while limiting direct contact and friction.
As a bushing wears, excessive clearance may develop in the corresponding pivot assembly.
Replacing a defective bushing with the correct OEM component helps restore the original suspension mounting arrangement.
The 112930 nylon bushing is identified by the manufacturer with the following specifications:
The four dimensions describe the bushing's specific geometry. Compare the complete shape and measurements with the original component before installation.
Important: A bushing with similar overall dimensions may not be interchangeable if its flange, mounting surfaces or profile differs.
Nylon is commonly used in mechanical bushings and bearing surfaces.
It provides an interface between moving components and helps reduce friction and direct wear on the adjacent parts.
In an ATV suspension system, bushings are exposed to repeated movement and varying mechanical loads.
Maintaining these components in good condition helps preserve the intended movement of the A-arms and prevent excessive pivot clearance.
Always follow the manufacturer's instructions regarding lubrication, assembly and maintenance.
Front suspension bushings should be inspected whenever excessive play is detected or an A-arm is removed during maintenance.
Common warning signs include:
These symptoms can also be caused by damaged mounting spacers, bolts or other suspension components.
Inspect the complete pivot assembly before determining which parts require replacement.
Before installation, disassemble the appropriate suspension components according to the recommended service procedure.
Inspect the mounting surfaces, spacers, bolts, locknuts and adjacent bushings for wear or damage.
Compare the replacement bushing with the original to confirm its shape and dimensions.
Install the new nylon bushing using an appropriate method that avoids damaging or deforming the component.
Use only the lubrication products or installation procedures specified by the manufacturer.
After reassembly, tighten the fasteners according to the applicable specifications and verify that the suspension arms move correctly without binding or excessive play.
The ATA125-K front suspension parts diagram lists 16 nylon bushings with part number 112930 in the complete assembly.
This is the number identified for the vehicle assembly, not the quantity included in this individual product listing.
For partial repairs, order the number of bushings required after inspecting the suspension and confirming the exact configuration of your ATV.
This part number may also be used on certain other TAO MOTORS ATVs. Verify the original part reference and bushing geometry before ordering for another model.
It is used in compatible front suspension A-arm pivot assemblies to help guide movement and reduce friction between the associated mechanical components.
Part number 112930 features nominal dimensions of 30 x 25 x 18 x 20 mm.
Yes. Part number 112930 is listed for the front suspension of the TAO MOTORS RAPTOR 125cc ATV.
The ATA125-K parts diagram lists 16 bushings with part number 112930. Confirm your specific vehicle configuration before ordering a complete replacement quantity.
This component is made of nylon. It should not be confused with the metal front suspension spacer, part number 112931.
Visible wear, cracking, deformation or excessive pivot play may indicate that a bushing needs replacement.
Yes. Part number 112930 identifies a genuine OEM TAO MOTORS replacement nylon bushing.
Yes. This listing is prepared for one nylon bushing per quantity ordered. Select the quantity required for your repair.
At EcoBike Canada, we offer a wide selection of genuine OEM replacement parts for TAO MOTORS ATVs.
Our parts selection includes nylon bushings, mounting spacers, bolts, nuts, suspension arms, shock absorbers and other front suspension components.
Benefit from our customer service, replacement parts selection and experience with recreational vehicle maintenance and repairs.
EcoBike – Your Canadian Source for Genuine TAO MOTORS OEM Parts.
www.eco-bike.ca